Chemical Precipitation

In an aqueous solution, precipitation is the "sedimentation of a solid material (a precipitate) from a liquid solution". The solid formed is called the precipitate. In case of an inorganic chemical reaction leading to precipitation, the chemical reagent causing the solid to form is called the precipitant.

The clear liquid remaining above the precipitated or the centrifuged solid phase is also called the supernate or supernatant.

The notion of precipitation can also be extended to other domains of chemistry (organic chemistry and biochemistry) and even be applied to the solid phases (e.g. metallurgy and alloys) when solid impurities segregate from a solid phase.

Supersaturation

The precipitation of a compound may occur when its concentration exceeds its solubility. This can be due to temperature changes, solvent evaporation, or by mixing solvents. Precipitation occurs more rapidly from a strongly supersaturated solution.

The formation of a precipitate can be caused by a chemical reaction. When a barium chloride solution reacts with sulphuric acid, a white precipitate of barium sulphate is formed. When a potassium iodide solution reacts with a lead(II) nitrate solution, a yellow precipitate of lead(II) iodide is formed.

Inorganic chemistry

Precipitate formation is useful in the detection of the type of cation in a salt. To do this, an alkali first reacts with the unknown salt to produce a precipitate that is the hydroxide of the unknown salt. To identify the cation, the color of the precipitate and its solubility in excess are noted. Similar processes are often used in sequence – for example, a barium nitrate solution will react with sulfate ions to form a solid barium sulfate precipitate, indicating that it is likely that sulfate ions are present.

A common example of precipitation from aqueous solution is that of silver chloride. When silver nitrate (AgNO₃) is added to a solution of potassium chloride (KCl) the precipitation of a white solid (AgCl) is observed.
:

The ionic equation allows to write this reaction by detailing the dissociated ions present in aqueous solution.
:

Reductive precipitation

The Walden reductor is an illustration of a reduction reaction directly accompanied by the precipitation of a less soluble compound because of its lower chemical valence:
:
The Walden reductor made of tiny silver crystals obtained by the immersion of a copper wire into a solution of silver nitrate is used to reduce to their lower valence any metallic ion located above the silver couple in the redox potential scale.

Colloidal suspensions

Without sufficient attraction forces (''e.g.'', Van der Waals force) to aggregate the solid particles together and to remove them from solution by gravity (settling), they remain in suspension and form colloids. Sedimentation can be accelerated by high speed centrifugation. The compact mass thus obtained is sometimes referred to as a 'pellet'.

Digestion and precipitates ageing

Digestion, or ''precipitate ageing'', happens when a freshly formed precipitate is left, usually at a higher temperature, in the solution from which it precipitates. It results in purer and larger recrystallized particles. The physico-chemical process underlying digestion is called Ostwald ripening.

Organic chemistry

While precipitation reactions can be used for making pigments, removing ions from solution in water treatment, and in classical qualitative inorganic analysis, precipitation is also commonly used to isolate the products of an organic reaction during workup and purification operations. Ideally, the product of the reaction is insoluble in the solvent used for the reaction. Thus, it precipitates as it is formed, preferably forming pure crystals. An example of this would be the synthesis of porphyrins in refluxing propionic acid. By cooling the reaction mixture to room temperature, crystals of the porphyrin precipitate, and are collected by filtration on a Büchner filter as illustrated by the photograph here beside:

:

Precipitation may also occur when an ''antisolvent'' (a solvent in which the product is insoluble) is added, drastically reducing the solubility of the desired product. Thereafter, the precipitate may be easily separated by decanting, filtration, or by centrifugation. An example would be the synthesis of Cr³⁺tetraphenylporphyrin chloride: water is added to the dimethylformamide (DMF) solution in which the reaction occurred, and the product precipitates. Precipitation is useful in purifying many other products: ''e.g.'', crude bmim-Cl is taken up in acetonitrile, and dropped into ethyl acetate, where it precipitates.

Biochemistry

Proteins purification and separation can be performed by precipitation in changing the nature of the solvent or the value of its relative permittivity (''e.g.'', by replacing water by ethanol), or by increasing the ionic strength of the solution. As proteins have complex tertiary and quaternary structures due to their specific folding and various weak intermolecular interactions (''e.g.'', hydrogen bridges), these superstructures can be modified and proteins denaturated and precipitated. Another important application of an antisolvent is in ethanol precipitation of DNA.

Metallurgy and alloys

In solid phases, precipitation occurs if the concentration of one solid is above the solubility limit in the host solid, due to e.g. rapid quenching or
ion implantation, and the temperature is high enough that diffusion can lead to segregation into precipitates. Precipitation in solids is routinely used to synthesize nanoclusters.

In metallurgy, precipitation from a solid solution is also a way to strengthen alloys.

Precipitation of ceramic phases in metallic alloys such as zirconium hydrides in zircaloy cladding of nuclear fuel pins can also render metallic alloys brittle and lead to their mechanical failure. Correctly mastering the precise temperature and pressure conditions when cooling down spent nuclear fuels is therefore essential to avoid damaging their cladding and to preserve the integrity of the spent fuel elements on the long term in dry storage casks and in geological disposal conditions.

Industrial processes

Hydroxide precipitation is probably the most widely used industrial precipitation process in which metal hydroxides are formed by adding calcium hydroxide (''slaked lime'') or sodium hydroxide (''caustic'' ''soda'') as precipitant.

History

Powders derived from different precipitation processes have also historically been known as 'flowers'.

See also

* Coprecipitation
* Effervescence, the "up-arrow"
* Precipitate-free zone
* Salting in
* Salting out

References

Further reading

*

External links

Precipitation reactions of certain cations

Digestion Instruments

A Thesis on pattern formation in precipitation reactions

{{DEFAULTSORT:Precipitation (Chemistry)
Liquid-solid separation