Argon–argon Dating

Argon–argon (or ⁴⁰Ar/³⁹Ar) dating is a radiometric dating method invented to supersede potassiumargon (K/Ar) dating in accuracy. The older method required splitting samples into two for separate potassium and argon measurements, while the newer method requires only one rock fragment or mineral grain and uses a single measurement of argon isotopes. ⁴⁰Ar/³⁹Ar dating relies on neutron irradiation from a nuclear reactor to convert a stable form of potassium (³⁹K) into the radioactive ³⁹Ar. As long as a standard of known age is co-irradiated with unknown samples, it is possible to use a single measurement of argon isotopes to calculate the ⁴⁰K/⁴⁰Ar* ratio, and thus to calculate the age of the unknown sample. ⁴⁰Ar* refers to the radiogenic ⁴⁰Ar, i.e. the ⁴⁰Ar produced from radioactive decay of ⁴⁰K. ⁴⁰Ar* does not include atmospheric argon adsorbed to the surface or inherited through diffusion and its calculated value is derived from measuring the ³⁶Ar (which is assumed to be of atmospheric origin) and assuming that ⁴⁰Ar is found in a constant ratio to ³⁶Ar in atmospheric gases.

Method

The sample is generally crushed and single crystals of a mineral or fragments of rock are hand-selected for analysis. These are then irradiated to produce ³⁹Ar from ³⁹K via the (n-p) reaction ³⁹K(n,p)³⁹Ar. The sample is then degassed in a high-vacuum mass spectrometer via a laser or resistance furnace. Heating causes the crystal structure of the mineral (or minerals) to degrade, and, as the sample melts, trapped gases are released. The gas may include atmospheric gases, such as carbon dioxide, water, nitrogen, and argon, and radiogenic gases, like argon and helium, generated from regular radioactive decay over geologic time. The abundance of ⁴⁰Ar* increases with the age of the sample, though the rate of increase decays exponentially with the half-life of ⁴⁰K, which is 1.248 billion years.

Age equation

The age of a sample is given by the age equation:
:$t=\frac \ln (J \times R+1)$
where λ is the radioactive decay constant of ⁴⁰K (approximately 5.5 x 10⁻¹⁰ year⁻¹, corresponding to a half-life of approximately 1.25 billion years), J is the J-factor (parameter associated with the irradiation process), and R is the ⁴⁰Ar*/³⁹Ar ratio. The J factor relates to the fluence of the neutron bombardment during the irradiation process; a denser flow of neutron particles will convert more atoms of ³⁹K to ³⁹Ar than a less dense one.

Relative dating only

The ⁴⁰Ar/³⁹Ar method only measures relative dates. In order for an age to be calculated by the ⁴⁰Ar/³⁹Ar technique, the J parameter must be determined by irradiating the unknown sample along with a sample of known age for a standard. Because this (primary) standard ultimately cannot be determined by ⁴⁰Ar/³⁹Ar, it must be first determined by another dating method. The method most commonly used to date the primary standard is the conventional K/Ar technique. An alternative method of calibrating the used standard is astronomical tuning (also known as orbital tuning), which arrives at a slightly different age.

Applications

The primary use for ⁴⁰Ar/³⁹Ar geochronology is dating metamorphic and igneous minerals. ⁴⁰Ar/³⁹Ar is unlikely to provide the age of intrusions of granite as the age typically reflects the time when a mineral cooled through its closure temperature. However, in a metamorphic rock that has not exceeded its closure temperature the age likely dates the crystallization of the mineral. Dating of movement on fault systems is also possible with the ⁴⁰Ar/³⁹Ar method. Different minerals have different closure temperatures; biotite is ~300°C, muscovite is about 400°C and hornblende has a closure temperature of ~550°C. Thus, a granite containing all three minerals will record three different "ages" of emplacement as it cools down through these closure temperatures. Thus, although a crystallization age is not recorded, the information is still useful in constructing the thermal history of the rock.

Dating minerals ''may'' provide age information on a rock, but assumptions must be made. Minerals usually only record the ''last time'' they cooled down below the closure temperature, and this may not represent all of the events which the rock has undergone, and may not match the age of intrusion. Thus, discretion and interpretation of age dating is essential. ⁴⁰Ar/³⁹Ar geochronology assumes that a rock retains all of its ⁴⁰Ar after cooling past the ''closing temperature'' and that this was properly sampled during analysis.

This technique allows the errors involved in K-Ar dating to be checked. Argon–argon dating has the advantage of not requiring determinations of potassium. Modern methods of analysis allow individual regions of crystals to be investigated. This method is important as it allows crystals forming and cooling during different events to be identified.

Recalibration

One problem with argon-argon dating has been a slight discrepancy with other methods of dating. Work by Kuiper et al. reports that a correction of 0.65% is needed. Thus the Cretaceous–Paleogene extinction (when the dinosaurs died out)—previously dated at 65.0 or 65.5 million years ago—is more accurately dated to 66.0-66.1 Ma.

See also

* Grenville Turner, inventor of the technique
* Berkeley Geochronology Center

References

External links

WiscAr Geochronology Laboratory, University of Wisconsin-Madison
* UC Berkeley press release:
Precise dating of the destruction of Pompeii proves argon-argon method can reliably date rocks as young as 2,000 years


New Mexico Geochronology Research Laboratory

Argon Isotope Facility
of the Scottish Universities Environmental Research Council

Open University Ar/Ar and Noble Gas Laboratory

Argon Laboratory / Australian National University

{{DEFAULTSORT:Argon-Argon Dating
Radiometric dating
Argon