|
Placement (electronic Design Automation)
Placement is an essential step in electronic design automation — the portion of the physical design flow that assigns exact locations for various circuit components within the chip's core area. An inferior placement assignment will not only affect the Integrated circuit, chip's performance but might also make it non-manufacturable by producing excessive wire-length, which is beyond available routing (electronic design automation), routing resources. Consequently, a placer must perform the assignment while optimizing a number of objectives to ensure that a circuit meets its performance demands. Together, the placement and routing steps of IC design are known as place and route. A placer takes a given synthesized circuit netlist together with a technology library and produces a valid placement layout. The layout is optimized according to the aforementioned objectives and ready for cell resizing and buffering — a step essential for static timing analysis, timing and signal integri ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Electronic Design Automation
Electronic design automation (EDA), also referred to as electronic computer-aided design (ECAD), is a category of software tools for designing electronic systems such as integrated circuits and printed circuit boards. The tools work together in a design flow that chip designers use to design and analyze entire semiconductor chips. Since a modern semiconductor chip can have billions of components, EDA tools are essential for their design; this article in particular describes EDA specifically with respect to integrated circuits (ICs). History Early days Prior to the development of EDA, integrated circuits were designed by hand and manually laid out. Some advanced shops used geometric software to generate tapes for a Gerber photoplotter, responsible for generating a monochromatic exposure image, but even those copied digital recordings of mechanically drawn components. The process was fundamentally graphic, with the translation from electronics to graphics done manu ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Field-programmable Gate Array
A field-programmable gate array (FPGA) is an integrated circuit designed to be configured by a customer or a designer after manufacturinghence the term ''Field-programmability, field-programmable''. The FPGA configuration is generally specified using a hardware description language (HDL), similar to that used for an Application-Specific Integrated Circuit, application-specific integrated circuit (ASIC). Circuit diagrams were previously used to specify the configuration, but this is increasingly rare due to the advent of electronic design automation tools. FPGAs contain an array of programmable logic device, programmable logic blocks, and a hierarchy of reconfigurable interconnects allowing blocks to be wired together. Logic blocks can be configured to perform complex combinational logic, combinational functions, or act as simple logic gates like AND gate, AND and XOR gate, XOR. In most FPGAs, logic blocks also include Memory cell (computing), memory elements, which may be simp ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Place And Route
Place and route is a stage in the design of printed circuit boards, integrated circuits, and field-programmable gate arrays. As implied by the name, it is composed of two steps, placement and routing. The first step, placement, involves deciding where to place all electronic components, circuitry, and logic elements in a generally limited amount of space. This is followed by routing, which decides the exact design of all the wires needed to connect the placed components. This step must implement all the desired connections while following the rules and limitations of the manufacturing process. Place and route is used in several contexts: * Printed circuit boards, during which components are graphically placed on the board and the wires drawn between them * Integrated circuits, during which a layout of a larger block of the circuit or the whole circuit is created from layouts of smaller sub-blocks * FPGAs, during which logic elements are placed and interconnected on the gr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Floorplan (microelectronics)
In electronic design automation, a floorplan of an integrated circuit is a schematics representation of tentative placement of its major functional blocks. In modern electronic design process floorplans are created during the floorplanning design stage, an early stage in the hierarchical approach to integrated circuit design. Depending on the design methodology being followed, the actual definition of a floorplan may differ. Floorplanning Floorplanning takes in some of the geometrical constraints in a design. Here are some examples: * bonding pads for off-chip connections (often using wire bonding) are normally located at the circumference of the chip; * line drivers often have to be located as close to bonding pads as possible; * chip area is therefore in some cases given a minimum area in order to fit in the required number of pads; * areas are clustered in order to limit data paths thus frequently featuring defined structures such as cache RAM, multiplier, barrel shifter, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Integrated Circuit Design
Integrated circuit design, or IC design, is a sub-field of electronics engineering, encompassing the particular logic and circuit design techniques required to design integrated circuits, or ICs. ICs consist of miniaturized electronic components built into an electrical network on a monolithic semiconductor substrate by photolithography. IC design can be divided into the broad categories of digital and analog IC design. Digital IC design is to produce components such as microprocessors, FPGAs, memories ( RAM, ROM, and flash) and digital ASICs. Digital design focuses on logical correctness, maximizing circuit density, and placing circuits so that clock and timing signals are routed efficiently. Analog IC design also has specializations in power IC design and RF IC design. Analog IC design is used in the design of op-amps, linear regulators, phase locked loops, oscillators and active filters. Analog design is more concerned with the physics of the semiconductor devic ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Design Flow (EDA)
Design flows are the explicit combination of electronic design automation tools to accomplish the design of an integrated circuit. Moore's law has driven the entire IC implementation RTL to GDSII design flows from one which uses primarily stand-alone synthesis, placement, and routing algorithms to an integrated construction and analysis flows for design closure. The challenges of rising interconnect delay led to a new way of thinking about and integrating design closure tools. The RTL to GDSII flow underwent significant changes from 1980 through 2005. The continued scaling of CMOS technologies significantly changed the objectives of the various design steps. The lack of good predictors for delay has led to significant changes in recent design flows. New scaling challenges such as leakage power, variability, and reliability will continue to require significant changes to the design closure process in the future. Many factors describe what drove the design flow from a set of ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Electronic Design Automation
Electronic design automation (EDA), also referred to as electronic computer-aided design (ECAD), is a category of software tools for designing electronic systems such as integrated circuits and printed circuit boards. The tools work together in a design flow that chip designers use to design and analyze entire semiconductor chips. Since a modern semiconductor chip can have billions of components, EDA tools are essential for their design; this article in particular describes EDA specifically with respect to integrated circuits (ICs). History Early days Prior to the development of EDA, integrated circuits were designed by hand and manually laid out. Some advanced shops used geometric software to generate tapes for a Gerber photoplotter, responsible for generating a monochromatic exposure image, but even those copied digital recordings of mechanically drawn components. The process was fundamentally graphic, with the translation from electronics to graphics done manu ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
IEEE Transactions On Computer-Aided Design Of Integrated Circuits And Systems
''IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems'' (sometimes abbreviated ''IEEE TCAD'' or ''IEEE Transactions on CAD'') is a monthly peer-reviewed scientific journal covering the design, analysis, and use of computer-aided design of integrated circuits and systems. It is published by the IEEE Circuits and Systems Society and the IEEE Council on Electronic Design Automation (Institute of Electrical and Electronics Engineers). The journal was established in 1982 and the editor-in-chief is Rajesh K. Gupta (University of California at San Diego). According to the ''Journal Citation Reports'', the journal has a 2020 impact factor of 2.807. Past editor-in-chief * Rajesh K. Gupta (2018-2022) * Vijaykrishnan Narayanan (2014-2018) * Sachin Sapatnekar (2010-2014) See also *Electronic design automation Electronic design automation (EDA), also referred to as electronic computer-aided design (ECAD), is a category of software tools for designing elec ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Clock Signal
In electronics and especially synchronous digital circuits, a clock signal (historically also known as ''logic beat'') oscillates between a high and a low state and is used like a metronome to coordinate actions of digital circuits. A clock signal is produced by a clock generator. Although more complex arrangements are used, the most common clock signal is in the form of a square wave with a 50% duty cycle, usually with a fixed, constant frequency. Circuits using the clock signal for synchronization may become active at either the rising edge, falling edge, or, in the case of double data rate, both in the rising and in the falling edges of the clock cycle. Digital circuits Most integrated circuits (ICs) of sufficient complexity use a clock signal in order to synchronize different parts of the circuit, cycling at a rate slower than the worst-case internal propagation delays. In some cases, more than one clock cycle is required to perform a predictable action. As ICs beco ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Application-specific Integrated Circuit
An application-specific integrated circuit (ASIC ) is an integrated circuit (IC) chip customized for a particular use, rather than intended for general-purpose use, such as a chip designed to run in a digital voice recorder or a high-efficiency video codec. Application-specific standard product (ASSP) chips are intermediate between ASICs and industry standard integrated circuits like the 7400 series or the 4000 series. ASIC chips are typically fabricated using metal-oxide-semiconductor (MOS) technology, as MOS integrated circuit chips. As feature sizes have shrunk and design tools improved over the years, the maximum complexity (and hence functionality) possible in an ASIC has grown from 5,000 logic gates to over 100 million. Modern ASICs often include entire microprocessors, memory blocks including ROM, RAM, EEPROM, flash memory and other large building blocks. Such an ASIC is often termed a SoC ( system-on-chip). Designers of digital ASICs often use a hardwar ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Integrated Circuit
An integrated circuit or monolithic integrated circuit (also referred to as an IC, a chip, or a microchip) is a set of electronic circuits on one small flat piece (or "chip") of semiconductor material, usually silicon. Large numbers of tiny MOSFETs (metal–oxide–semiconductor field-effect transistors) integrate into a small chip. This results in circuits that are orders of magnitude smaller, faster, and less expensive than those constructed of discrete electronic components. The IC's mass production capability, reliability, and building-block approach to integrated circuit design has ensured the rapid adoption of standardized ICs in place of designs using discrete transistors. ICs are now used in virtually all electronic equipment and have revolutionized the world of electronics. Computers, mobile phones and other home appliances are now inextricable parts of the structure of modern societies, made possible by the small size and low cost of ICs such as modern compute ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Design Closure
Design Closure is a part of the digital electronic design automation workflow by which an integrated circuit (i.e. VLSI) design is modified from its initial description to meet a growing list of design constraints and objectives. Every step in the IC design (such as static timing analysis, placement, routing, and so on) is already complex and often forms its own field of study. This article, however, looks at the overall design closure process, which takes a chip from its initial design state to the final form in which all of its design constraints are met. Introduction Every chip starts off as someone’s idea of a good thing: "If we can make a part that performs function X, we will all be rich!" Once the concept is established, someone from marketing says "To make this chip profitably, it must cost $C and run at frequency F." Someone from manufacturing says "To meet this chip’s targets, it must have a yield of Y%." Someone from packaging says “It must fit in the P p ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> Integrated Circuit")